xlpe black for cable

Cross-linked polyethylene, which is said xlpe to be made of polyethylene, is based on linear light density polyethylene LLDPE and heavy density polyethylene.

An obvious xlpe feature is the increase in mechanical and thermal properties compared to polyethylene.

This process turns polyethylene into cross-linked polyethylene

It greatly increases its mechanical properties and temperature tolerance so that it can perform better xlpe cables than pvc.

Xlpe Black is one of the most widely used cross-linked polyethylene granules, which is coated with soot carbon and used in cable factories.
xlpe black for cable creates a strong protective layer on the outer surface of the cable that is most resistant to mechanical and thermal stresses.

The advantages of the product can be high mechanical properties ,anti-uv , acid rain position ,excellent conductivity , high thermal resistance , no Drying and …

Pitaris factory, a producer of xlpe black and xlpe natural, has the ability to supply xlpe for cable factories and traders with the best quality and conditions.
xlpe is always important in the cable industry and greatly improves the quality of work, especially for high voltages and sensitive places, so the supply of xlpe is very important.

xlpe black granola

Low-temperature impact strength, abrasion resistance and environmental stress cracking resistance can be increased significantly by crosslinking, whereas hardness and rigidity are somewhat reduced.

xlpe does not melt any more (analogous to elastomers) and is thermally resistant (over longer periods of up to 120 °C, for short periods without electrical or mechanical load up to 250 °C). With increasing crosslinking density also the maximum shear modulus increases (even at higher temperatures)

A low degree of crosslinking leads initially only to a multiplication of the molecular weight. The individual macromolecules are not linked and no covalent network is formed yet. Polyethylene that consists of those large molecules behaves similar to polyethylene of ultra high molecular weight like a thermoplastic elastomer.

Upon further crosslinking the individual macromolecules are eventually connected to a network. This crosslinked polyethylene is chemically seen a thermoset, it shows above the melting point rubber-elastic behavior and can not be processed in the melt anymore.
The degree of crosslinking is different in intensity depending on the process. According to DIN 16892 at least the following degree of crosslinking must be achieved:

in peroxide crosslinking (PE-Xa): 75%
with silane crosslinking (PE-Xb): 65%
with electron beam crosslinking (PE-Xc): 60%
in azo crosslinking (PE-Xd): 60%

Supplier xlpe black

Pitaris Manufacturer of Crosslinkable HDPE Compound for multilayer Pipe and Crosslinkable LLDPE Compound for Cable

Produces xlpe natural and xlpe black, distributes and sells directly. Our goal is to create the best conditions and supply goods for traders and consumers. You can contact us and check our products.

 

Packing:25 KG special bags

 

PE wax suppliers in Vietnam

The biggest problem for plastic manufacturers is injection. The problem is usually the lack of injection of the full form due to the lack of adhesion of the device
The supply of polyethylene wax is a solution, PE wax which is always used in the industry, has increased the demand for PE wax and the PE wax suppliers with the increase of the market volume and the increase of per capita consumption of PVC.

Pitaris factory has created work for consumer industries and traders by PE wax suppliers in the market and exporting it.

PE wax is one of the products of Pitaris factory , which offers this product in the market with quality and competitive price, and seeks to create a strong network for the export and distribution of goods

Choosing PE wax has always been a challenge. We try to make it easy for you

What is PE wax

Polyethylene wax is a low molecular weight polyethylene polymer that is practiced for improving and enhancing the method parameters and characteristics of the finished products in diverse papers in the plastic industry. It has low molecular weight and stresses wax-like
characteristics. There are various companies that are engaged in offering quality non-oxidized, non-polar PE wax. The wax is expressed using the distillation process for enhancing the characteristics of the product and to produce different grades of PE wax. The excellent properties of PE wax make it a required element in the plastic industry. ac-6a and A-C PE  Homopolymer Waxes or polyethylene wax ac 6a is a more complicated type and kind of pe wax. this type has a harder and better formula and it has its own special applications as well. they have to create this type of PE wax in different labs.

PE wax supplier for trade

For more information about the catalog and technical specifications of Pitaris polyethylene waxes, you can refer to the products section of the site or contact the sales consultants. In this news, we intend to ensure your ability to meet your orders.
One of the services is product optimization at the request of customers and merchants for the target market in order to create the best feedback and cooperation. In this competitive environment, price and quality should definitely have a place.

traders and consumers can use the registration their information by email and special conditions and offers of Pitaris company

PE wax price market

PE wax price market

According to the per capita consumption PVC , it is possible to increase the importance of the consumption of PE wax market, which increases the per capita consumption of PE wax price .

Economists believe that the volume of the PE wax price market will jump by 4.5% per year by 2024 ,It is important to supply and distribute PE wax and network market

The price of PE wax can be considered from the base price of polyethylene, which increases the quality according to the physical condition, density, purity of volatile materials. We recommend that you select and order the appropriate PE wax product according to the industry and production process, so that it has the best effect and feedback.

 

 

PE wax supplier

 

Pitaris Company, having several factories in the field of production of polymers and additives, is one of the factories of Pitaris, which is responsible for the production of various types of polyethylene wax, which directly contracts with agencies and traders active in each country and provides sales with the best conditions. And offers its products

polyethylene wax price

The price of polyethylene wax should be considered by considering the quality, industry used and volume of goods
Due to 8 years of experience in the production and export of PE wax, Pitaris has tried to offer different types of PE wax to the market in terms of price and quality in order to have a stronger cooperation in the market and buyers.

You can use our economical grades with suitable quality and a maximum impurity of 2%. It is offered in 25 kg bags and is most used in the PVC industry and pipes and masterbatch for high volume consumption and traders.

on the other hand, there are special high quality grades for special industries and companies that are used for hot adhesives and other industries.

Pitaris can produce PE wax based on buyer analysis and optimize it to achieve the best conditions

You can get PEwax Pitaris products and technical information from the site Email us for advice and cooperation

 

xlpe black granola manufacturer in china

Xlpe black granola manufacturer in china

Cross-linked polyethylene, which is trademark xlpe , XLPE insulated cables are ideal for transmitting higher voltage without hindrance or compromise to its effectiveness. Thanks to their remarkable insulation properties, XLPE insulated cables surpass other alternative insulation materials like Silicon rubbers, and even Ethylene Propylene Rubber, EPR.

The list of  xlpe applications is endless and every industry where it’s been utilized takes advantage of one or more of its unique properties. In mines, for instance, it’s the ability to withstand extremely high pressure and temperature and still maintain its toughness that makes it a suitable material.

China, one of the leading industries in the field of production of power cables and composite materials, has a significant need for xlpe black and xlpe natural for the market and industry.

Pitaris the manufacturer xlpe granolasin the Middle East is trying to supply the market and establish a network with traders.

 

 

Xlpe black granola  for wire company

Compared to ordinary polyethylene, cross-linked polyethylene xlpe black granola has enhanced properties that give it an added advantage in performance.

xlpe black wire with its improved properties doesn’t melt easily and can withstand higher temperatures of up to 120°C for an extended time without losing its mechanical and chemical properties. The young modulus is also increased as well as its resistance to abrasion and environmental stress. The cross-link of the polymer structure changes the thermoplastic into a thermoset, hence the resultant improvement in xlpe properties as discussed.

Cross-linking xlpe insulation cables can best be described as vulcanizing the rubber with the addition of littles amounts of chemical additives to help rearrange the molecular structure into a lattice that hinders the movement of molecules in the presence of heat.

Hence, xlpe black granules have been replaced pvc in cable factories and have become the primary cases of making black cables.

 

 

Pitaris the manufacturer xlpe granolas

Low-temperature impact strength, abrasion resistance and environmental stress cracking resistance can be increased significantly by crosslinking, whereas hardness and rigidity are somewhat reduced. PEX does not melt any more (analogous to elastomers) and is thermally resistant (over longer periods of up to 120 °C, for short periods without electrical or mechanical load up to 250 °C). With increasing crosslinking density also the maximum shear modulus increases (even at higher temperatures). PEX has significantly enhanced properties compared with ordinary PE. Crosslinking enhances the temperature properties of the base polymer. Adequate strength to 120–150 °C is maintained and chemical stability enhanced by resisting dissolution.

A theoretically extreme degree of cross-linking is reached if only –CH2– bridges are placed between cross-linkings that are also –CH2– bridges and if the polymer structure’s sum formula is (C3H4)n, then the structure is that of a diamond with all bonds replaced by –CH2– bridges. If 4 vertices of a cube c are placed where C-atoms of the diamond base are so that only one further diamond base atom lies inside c then 4 diamond base bonds lie in c and—because the bond angles are forced towards such maximal values that also here a diamond cubic crystal structure is already approached—it is expected that the C-atoms of these –CH2– bridges are posed on lines that are both orthogonal to diamond base bonds and parallel to faces of c.

Almost all cross-linkable polyethylene compounds (XLPE) for wire and cable applications are based on LDPE. XLPE-insulated cables have a rated maximum conductor temperature of 90 °C and an emergency rating up to 140 °C, depending on the standard used. They have a conductor short-circuit rating of 250 °C. XLPE has excellent dielectric properties, making it useful for medium voltage—1 to 69 kV AC, and high-voltage cables—up to 380 kV AC-voltage, and several hundred kV DC.

 

Connect and cooperation with pitaris

we produce and offer our products according to international standards(ASTM) and technical sheets
xlpe granola  has a higher quality, productivity and efficiency due to its process properties, but we always try to offer the best quality at the best price together.

Pitaris is ready to sell its products to traders and consumers with the best conditions
Please contact us to view the xlpe black granola catalog in the products section or by sending an email to us or authorized Pitaris dealers.

 

 

xlpe black in china

xlpe black in china

Cross-linked polyethylene(xlpe) ,xlpe black china Used in cable industries and cable factories

xlpe black Insulated Steel Wire Armored PVC Sheathed YJV32 Power Cables, copper conductor, XLPE insulation, PVC inner sheath, steel wire armoured, PVC out sheath, U0/U: 0.6/1kV.

It applies to electrical power transmission and distribution lines with AC rated voltage U0/U up to and including 0.6/1kV. For outdoor and indoor installation in damp and wet locations, laid directly in the ground where excessive mechanical stresses are present in sloping and moving terrains and in vertical or inclined laying, as well as in locations susceptible to sliding.

What is xlpe black

Also known as Cross-linked Polyethylene, XLPE is a very good insulation in terms of electrical properties. XLPE has very high insulation resistance, a stable dielectric constant over all frequencies, and a low dielectric constant.

Features & Advantages of xlpe black Wire & Cable:
In terms of flexibility, polyethylene can be rated stiff to very hard, depending on molecular weight and density (low density being the most flexible). Black and specially formulated colored versions have excellent weather resistance.

  • Moisture resistant
  • Impressive electrical and physical properties
  • xlpe cables are capable of carrying large currents due to excellent thermal resistance
  • Easy to Install and maintain with cables being light in weight

Manufacturer granule xlpe black

Petaris Company is a manufacturer of PE wax, cross-linked polyethylene (XLPE) in the Middle East, which sells its products according to technical sheets and catalogs.
The main focus of this company is to export the best quality xlpe black for the market
Pitaris has provided direct supply of xlpe to cable companies with good conditions

The Chinese market Due to the high consumption of plastics and leading in the field of polymers, the production of high pressure power cables is important for this market, so the supply of xlpe black China is important for traders.

Crosslinkable LLDPE Compound Pitaris

one of the products of Pitaris company Crosslinkable LLDPE Compound(xlpe) ,The products are used in the form of granules for power cables and five-layer pipes
This product with high thermal and mechanical resistance is important for industries.

Pitaris is ready to cooperate with the best conditions for cable factories to provide a strong network of production and supply.
Products with special packaging and vacuum 25 kg
Email us for advice and purchase of products

PE wax price market

PE wax price market

China is known as the largest country in the field of consumption of PE wax and plastic industry
PE wax is one of the additives in the plastics industry and is used as a process aid in the plastics industry.

It is very important to know and study the PE wax china market and PE wax price in china ,Pitaris Company publishes this article for traders based on its experience and activity in the PE wax chain market

Rising demand for polyvinyl chloride (PVC) will be a major driver of market size for polyethylene wax (PE wax) in the near future,

 

 

Pitaris products

Pitaris Company, a manufacturer of PE wax, cross-linked polyethylene(XLPE), polyethylene products, seeks to provide an article in the presence of PE wax market for traders, wax distribution networks and PE wax chain importers

China is the most widely used country in the plastics industry, and PE wax chain is important for price reviews. Due to the communication channels and distribution network of PE wax Pitaris in China, it has made it possible to import PE wax china and communicate with traders.

 

PitarisPE wax is ideally used in the powder, flakes and pellets forms. The powder form led the market in 2016 and is estimated to follow the same trend over the forecast timespan. For instance, Pitaris states that the Pastil form with diverse viscosities results in better blending with other raw materials and easy processing. pastil form improves the flow of PE compounds, provides thermal stability & color stability, unique organoleptic characteristics and ideal dispersing properties for fillers, pigments and additives. PE wax can thus be used as an effective matting agent for wood coatings and other applications.

PE wax supplier china

Pitaris can supply PE wax with the lowest price and quality requested by the customer and its main focus is exports with regard to exports to African and European countries.
It also provides PE wax with the best conditions for China
You can refer to Pitaris website to get complete news information and technical information sheet of products and select your desired product.
Contact us for price and sales advice.

PE wax china price

PE wax china price

Polyethylene wax or PE wax , which is a by-product in petrochemicals and is used as an additive in various industries. This product has a high importance and prestige in the plastics industry. One of the largest consumers in the world for PE wax in China. That is why PE wax is important in China for manufacturers and traders.PE wax is evaluated and priced based on specifications and technical information. PE wax price china can be evaluated from suppliers and trade networks.

 

Manufacturers PE wax

In addition to price PE wax, you should consider quality and technology. Quality in the product is very important because it participates in important processes

Pitaris Factory is a manufacturer of polyethylene waxes(PE wax), polyethylene cross-linked(XLPE) and plastic additives with 8 years of production and supply in the Middle East.
Pitaris has provided activities in China to offer the best PE wax price china so that traders can inquire about prices from this company and by providing advice so that results and cooperation with traders.

 

Prices of different types of PE wax

Before examining the PE wax chain and PE wax price , we should know more about the product and get acquainted with it.

1-PE wax

2- OPE wax

3-emulsion wax

PE wax the most common types have a high per capita consumption
In terms of chemical properties, PE wax is divided into two categories: low density and high density, which affects the price of the product. Another factor is the purity of this product from volatile substances. To check the appearance of PE wax, it should be white and transparent. It is important

Buy and trade PE wax china

Pitaris tries to supply the product at the best price by establishing contacts with distributors, traders and sales agencies. You can get PEwax Pitaris products and technical information from the site
Email us for advice and cooperation

PE wax china supplier

PE wax china supplier

Pitaris factory is a manufacturer and supplier PE wax (polyethylene wax), which has a special activity in the field of supplying PE wax china for Chinese industries.

Polyethylene wax, PE Wax china Due to the size consumption of China’s industry, PE wax supply is important for China. You can get more information from authorized dealers or ask us.  you can check the technical information and projects inside the site

The goal of Pitaris company is to provide the right PE wax to the customer’s needs and to create a strong network of traders in this industry

PE wax

Polyethylene wax is a ultra low molecular weight polyethylene based on ethylene monomer china.
Primarily its available as by-product from polymerization of crude oil cracking into ethylene and categorized into LDPE wax and HDPE wax accordingly and further on-purpose modified with specific required values including oxidized waxes as well.
It has large variety of applications to improve processing and uses. Global demand of PE Wax is continuously increasing and FT wax has also played very good role in some applications as PE Wax alternative.
It is important to mention that different practices are being carried out to obtain PE Wax from PE scraps to cop up with price issues and an alternative channel to obtain scrap wax specially when petrochemicals focus on obtaining final PE product instead of any by-product.
China is largest user of waxes in the world and recent Crona virus attack has set back their economy that can impact a lot on related industry worldwide.

PE wax application

PE wax (Polyethylene wax) has special properties and is used in various industries that play an additive role and improve performance.

  • Inks
  • Paint
  • Engineering Plastic (Composites)
  • Masterbatch
  • PVC extrusion
  • lubrication
  • Hot Melt Adhesive
  • Pigment dispersion
  • Additives and stabilizers
  • Polishes
  • processing

Pitaris PE wax china

Pitaris Company is a manufacturer of various types of PE wax (Polyethylene wax), OPE wax( oxidized Polyethylene wax) which is produced with high density HDPE and low density LDPE according to the standard of technical sheets TDS

Pitaris is a manufacturer of PE wax in the Middle East and its focus is on the East Asian market distribution  and supply network, Quality and price , Communication route and low shipping cost are our other advantages.

One of the best-selling special product is the PE wax grade LP105 , which is an HDPE wax which makes it possible to compete in terms of quality and price. and with good experience we offer to trade

HDPE LP105

PE wax LP105

The appearance of this product is flake thin and shiny
Packed in bags of 25 kg in BOPP

To contact us and inquire, refer to the email or WhatsApp

Supplier PE wax in Turkey

Supplier PE wax in Turkey

PTA  PE wax is polyethylene homopolymer wax, an excellent and consistent ingredient for end formulations to improve product physical appearance and thermal properties for a broad range of industries, including hot melt adhesives, PVC, color masterbatches, rubber and thermoplastics road markings, etc.

Pitaris the manufacturer of all kinds of PE wax supplies its products to Turkey and is ready to cooperate and offer products with the best quality and price to the Middle East.

How are PE wax made?

There are a variety of methods for producing PE wax. Polyethylene wax can be made by direct polymerization of ethylene under special conditions that control molecular weight and branching of the polymer. Another method involves breaking down high molecular weight polyethylene resin into lower molecular weight fractions. A third method involves separation of the low molecular weight fraction from a production stream of high molecular weight polymer. These last two methods produce very low molecular weight fractions that should be removed to avoid a product with low flash point that can result in flammability, migration and other safety issues.

Type of PE wax in Turkey

Pitaris PE wax products are generally divided into three categories:

  • Non-polar polyethylene wax (PE wax)
  • Oxidized polyethylene wax (OPE wax)
  • Polyethylene wax emulsion

For more information about this product and to view its technical data sheet, please refer to the section products

High quality PE wax in Turkey

PE wax have a great variety due to their consumption and use in different industries and it is mentioned as an important additive in the industry and we always recommend this product according to the consumption and needs of each industry.

we produce and offer our products according to international standards(ASTM) and technical sheets
Oxidized polyethylene wax has a higher quality, productivity and efficiency due to its process properties, but we always try to offer the best quality at the best price together and pursue the ability to PE wax cost-effective so that we can reach all customers.

Please send us your request to Email or inquiry form